This is a high strength leaded silicon manganese bronze with typically good bearing qualities. This alloy maintains high impact resistance with excellent machinability making it well suited for clutch bearings, shaft bushings, sleeve bearings, thrust bearings, pump parts, drive shafts, bearing pins, wear plates, gears and cams. Resists squashing out under high loads and extreme wear applications.
Fasteners, Lead Screw Nuts
Gears and Cams, Wear Plates, Bushings, Seal Rings, Idler Pins, Piston Heads, Brearing Pins, Thrust Bearings, Sleeve Bearings, Propeller Shafts, Shaft Bushings, Clutch Bearings, Drive Shafts, Spindles, Pump Parts, Bearings
Hardware, Valve Seats
Connecting Rods
Cu% | Sn% | Pb% | Zn% | Fe% | Ni% | AI% | Mn% | Si% |
---|---|---|---|---|---|---|---|---|
58.0 - 63.0 | 0.30 | 0.40 - 3.0 | Rem. | 0.5 | 0.25 | 0.25 | 2.0 - 3.5 | 0.50 - 1.5 |
Mechanical - H02 Half Hard: upto 1” inclusive | ||
---|---|---|
Tensile Strength, min | 65 ksi | 448 MPa |
Yield Strength @ .5% ext under load min | 40 ksi | 276 MPa |
Elongation in 2 in. or 50 mm min, % | 12 | |
Brinell Hardness | N/A | |
Machinability Rating | 70% |
Mechanical - H02 Half Hard: over 1” to 3” inclusive | ||
---|---|---|
Tensile Strength, min | 58 ksi | 400 MPa |
Yield Strength @ .5% ext under load min | 35 ksi | 241 MPa |
Elongation in 2 in. or 50 mm min, % | 15 | |
Brinell Hardness, min | N/A | |
Machinability Rating | 70% |
Mechanical - H02 Half Hard: over 3” | ||
---|---|---|
Tensile Strength, min | 55 ksi | 380 MPa |
Yield Strength @ .5% ext under load min | 30 ksi | 205 MPa |
Elongation in 2 in. or 50 mm min, % | 18 | |
Brinell Hardness, min | N/A | |
Machinability Rating | 70% |
US Customary | Metric | |
---|---|---|
Melting Point-Liquidus | 1605 °F | 874 °C |
Melting Point-Solidus | N/A | N/A |
Density | 0.3 lb/in 3 @ 68 °F | 8.3 gm/cm 3 @ 20 °C |
Specific Gravity | 8.3 | 8.3 |
Electrical Resistivity | N/A | N/A |
Electrical Conductivity | 22% IACS @ 68 °F | 0.13 MegaSiemens/cm @ 20 °C |
Thermal Conductivity | 55 Btu/sq ft/ft hr/°F @ 68 °F | 95 W/m @ 20 °C |
Coefficient of Thermal Expansion | 11 ⋅ 10-6 per °F (68-572 °F) | 19 ⋅ 10-6 per °C (20-300 °C) |
Specific Heat Capacity | N/A | N/A |
Modulus of Elasticity in Tension | 17000 ksi | 117212 MPa |
Magnetic Permeability | N/A | N/A |